Why 1050 / 1070 Aluminum Cold Extrusion + CNC Machining Beats Die Casting for Automotive ADAS Camera Housings

Table of Contents

Custom Parts Service, Contact Us Now!

As autonomous driving and Advanced Driver Assistance Systems (ADAS) evolve from 1-megapixel backup cameras to 8-megapixel 360° Surround-View (AVM) and forward-sensing optical modules, automotive camera housing design faces three simultaneous engineering challenges: high heat flux in a miniature sealed box, micron-level optical lens alignment, and zero-particle internal cleanliness.

Many engineering teams initially prototype camera shells by 5-axis CNC machining from 6061 billet, or attempt mass production via traditional ADC12 aluminum die casting—only to discover that billet CNC is too expensive for 100,000+ annual volumes, while die-cast ADC12 suffers from poor thermal conductivity (~96 W/m·K), anodizing blemishes, and laser-welding porosity.

Here is how Xiamen Mindwell Precision Manufacture Co., Ltd. solves this trade-off using AA 1050 / 1070 Pure Aluminum Cold Extrusion (Cold Forging) + Precision CNC Finishing + Magnetic Tumbling Polishing & Anodizing.

Internal view of 1050 and 1070 pure aluminum cold-extruded and CNC precision machined automotive ADAS camera upper and lower housing showing PCB positioning pins and waterproof sealing step
Mindwell’s 1050/1070 pure aluminum cold-extruded & CNC-machined automotive camera upper and lower housings showing integral PCB alignment pins and interlocking waterproof sealing steps.

1. Why AA 1050 / 1070 Cold Extrusion Beats ADC12 Die Casting for Automotive Camera Enclosures

Performance Metric 1050 / 1070 Cold Extrusion + CNC (Mindwell Solution) ADC12 High-Pressure Die Casting 6061 Full Billet CNC Machining
Thermal Conductivity 222 – 234 W/(m·K) (Best Passive Cooling) 92 – 96 W/(m·K) (Prone to Thermal Throttling) 167 W/(m·K)
Internal Porosity & Density 100% Pore-Free Wrought Grain Flow Contains Subsurface Micro-Porosity 100% Pore-Free
Anodizing Quality Flawless Clear, Silver, or Black Anodizing Gray/Mottled Smut due to 10%+ Silicon Excellent
Mass Production Unit Cost 50%–65% Lower than Full Billet CNC Low Very High (75%+ Chip Waste & Long Cycle Time)

2. Inside Mindwell’s 4-Stage Manufacturing Workflow

Stage 1: Single-Stroke Backward & Forward Cold Extrusion

Starting from precision-sheared and lubricated AA 1050 or AA 1070 pure aluminum slugs, our high-tonnage cold forging press extrudes both the Upper Front Lens Housing and Lower Rear Connector Housing to near-net shape in a single stroke:

  • On the Rear Shell, forward extrusion forms the thin-walled cylindrical FAKRA coaxial connector sleeve complete with its outer anti-rotation locking tab, while backward extrusion forms the deep inner PCB pocket and corner mounting bosses.
  • On the Front Shell, cold forging simultaneously extrudes the square outer skirt and three integral PCB positioning pins (`Ø1.5–2.0 mm`) directly from the inner floor—eliminating separate dowel-pin assembly.
Close-up of automotive surround-view camera front aluminum shell featuring CNC single-point threaded optical lens barrel, magnetic tumbled burr-free texture, and clear anodized finish
Assembled 1050/1070 cold-forged aluminum automotive camera housing showing rear cylindrical FAKRA connector tube with integral anti-rotation locking tab and mounting holes

Stage 2: High-Precision CNC Turning & Milling (`±0.01 mm`)

Because pure 1050/1070 aluminum is soft and ductile (“gummy” during cutting), standard tooling can leave built-up edges. Mindwell utilizes diamond-coated/polished carbide cutters and high-pressure coolant on our 4-axis CNC centers to machine:

  1. Fine-Pitch Optical Lens Internal Threads: Single-point CNC thread-turned/milled to guarantee ≤ 0.015 mm optical axis perpendicularity relative to the internal PCB mounting bosses.
  2. Interlocking Waterproof Rabbet Step: Precision contour-milled along the upper and lower shell perimeter (`±0.01 mm`) to ensure an IP67 / IP69K hermetic seal.
  3. Rear Mounting Datum Pads & Corner Holes: Face-milled for flat vehicle bracket seating (`Photo #4`).

Stage 3: Magnetic Tumbling Polishing (360° Micro-Burr Removal)

To prevent any metallic micro-burr from detaching onto the camera’s CMOS sensor or short-circuiting the PCB, all housings are processed in automated magnetic pin tumblers. High-frequency rotating magnetic fields drive fine stainless-steel pins through every thread root, blind pocket, and connector bore—deburring and work-hardening the surface into a uniform matte texture without rounding off critical CNC sealing edges.

Stage 4: Automotive-Grade Anodizing & Ultrasonic Cleanroom Packaging

Finally, the housings receive protective clear/silver or optical matte-black anodizing (or hex-free passivation where electrical grounding continuity is required), followed by multi-stage ultrasonic cleaning and blister-tray packaging.

Comparison of custom 1050 1070 aluminum cold-forged automotive camera housings with CNC milled datum pads, magnetic tumbling polishing, and anodized corrosion protection
Assembled 1050/1070 cold-extruded & CNC-machined automotive camera shells demonstrating precision seam fit and CNC-milled datum surfaces.

👉 Explore our full specification page: Custom 1050 / 1070 Aluminum Cold-Extruded & CNC Machined Automotive ADAS Camera Housing, or Contact Our Engineering Team with your 3D CAD drawings for a free 24-hour DFM review and quotation!

Related Blogs